Видео

Thank you so much!

Any idea why the Speed 60 setting on my Bosch dishwasher runs for 124 minutes? I called their helpline but the lady was inexperienced and offered no help. Also one of the other buttons is depressed (stuck) and I can’t get it to move back up. (So disappointed in this expensive purchase.)

Fantastic and very helpful. My dryer was rattling - cleaned the lint out of the blower as you showed and it's back to normal. Thanks for this vodeo!

If your latch is not locking when going to a rinse or spin cycle the lid lock may not be your issue. The plastic latch that is on the door just need to be pushed down a little more so the lid lock can lock it. My solution to this was to just use some electrical tape and add some length to that plastic lid latch. I took the plastic lid latch off (two screws) and added electrical tape to the end of that piece that does not latch into the lid lock. So added little by little and then screwed it back in. You need to make sure that the plastic lid latch is lining up properly but this solution seems to be working for me. And I did replace the lid lock and the issue was still there. Wish I could add a picture to really show you but hopefully that helps someone.

❤

So what was the problem, it looks like all of them had continuity

It certainly does NOT Dry Dishes and the smaller one doesn’t have the simple cycle Rinse then hold So you rinse dishes so they clean easily later when you can fill it full and run it then. Even the Hotpoint Dishwasher has rinse and hold. And Dries the dishes

Thank you!

Thank you for this video! I got my dryer fixed 😊

What do you do if the ignition doesn’t properly light after changing?

my oven will not turn off

And that did nothing

Thanks for posting

Thank you so much, was able to fix our washer after watching your video. 👍🏼

You are awesome sir! Reset worked and ordering another one now! Thank you very much!

I purchased and installed the new circuit board and checked each end of the power supply but no buttons on the control panel are lit. i do see a faint green light on the circuit board itself. Any thoughts?

Thank you soooo much

Bloomberg is the worse brand I ever, ever got for a dryer. It never dried correctly, never even finished a cycle for the full time according to the time it shows: always stops before because of the filter, even if the filter is almost totally clean (???). And this has been the case since the beginning (have it for only 2 years). I tried everything from the instruction and nothing works. Such a piece of c****p!

Mine drains and pump kicks on. But it doesn’t spin. But if the doors not closed all the way it won’t start at all. Is there a different sensor in this that would cause this problem? Because seem like the door switch works.

Thank you so much for this lol! My dryer stopped and wouldn’t start couldn’t figure out what it was until I watched this. All I did was put more pressure on the door and started the dryer and it came right on! 👍🏽

Thank you. That was helpful.

I have a Miele model G2472 , do you know if the water inlet valve is the same one as you replaced in this video ? I cannot find it listed on the website for the replacement you used from Amazon , thanks

Great video! Had a very noisy dryer, followed this video and cleaned everything out. Now it’s back to normal! Thanks!

This is awesome, thanks! Worked a treat

What brand and model of wrist watch is that? Thanks

Thank you so much! There were a few things in the cleanout but up in drain opening off of it there was a little glasses cleaning rag that had stopped the washer completely. You are much appreciated!!😀

Video helped me out. Unfortunately my water pump had a snapped propeller thing. Amazon has the entire pump for $40 bucks plug and play.

Great walkthrough! This worked for me. Subscribed!

My front loading Blomberg won't start agitating once the water starts coming into the drum. It won't spin at all if i set the program to spin only. The door does lock when i turn on the machine and won't open until i cancel the program. Does this mean that a broken lock is not the problem and something else is causing it not to spin? Thanks so much for your help.

Thank you. Saved me at least $125 as co pay on home warranty. 👍👍👍

Thank you for this.

It clicked the dryer ran and heat it up again but the next time I run the dryer it didn't heat up and the button was out again. Tested both sensors and they both have continuity my igniter is only testing 0.20 does that mean that I need to replace the igniter

Immma need this in about a week for the trip buttons. 🤣🤣🤣☠️☠️☠️

genius. please be my friend

Try checking the flat tube at the back of the dishwasher and run on the bottom of the top rack. It moves the water from the bottom to the top spray arm. See if you can remove it and see if it’s blocked or has buildup.

I'm not sure what my part number would be for my wssh300g0ww wax moter. I've looked & looked. A new lid lock is over $300.

My freezer door whirlpool gold down screw that hold the trey rail and door was broken..left side of it. How do i replace the with screws. The broken screw side is always open..I need to buy the freezer to replace the broken screw door. How can I get the door with both screws intact pls.

A hand held steamer works really well for steaming out the drain hole and removing ice

I have been trying for hours to slide the bellow over the plastic cylinder at the bottom, but it keeps popping out. Any suggestions on how to keep it from doing that? I need to get this done, please.

Yessir this def works

A small black rubber tube near the bottom and just inside the rear access panel came detached from whatever it was supposed to be attached to ( I am not certain what it was) on our LG frontload washing machine and flooded our laundry room, hall, kitchen, and basement. Yes, one small detached rubber tube caused all of that. I did not find any clamp, so I reattached the tube (to whatever it is) and taped it for extra security.

Thank you so much for making this video! Such a simple fix that saved us so much time and money! I’m also amazed at how clean this oven is… 😂 One word of caution to anyone looking to replicate the steps in this video, my connector to my igniter fell back into the oven once I disconnected it. I had to fish it out with measuring tape which cost me more time than the rest of the job. So my advice is to PULL THE CONNECTOR OUT AS FAR AS YOU CAN AND SECURE IT before unclipping the old igniter. Thank you again for this video! Felt good to do the job myself. 😊

What’s name of part that I can order from amazon?

Thank you so much for this helpful video. I'm not handy so when I pulled this off (thanks to you) it was a small but tremendous feeling of personal accomplishment for me. Really appreciate this - will watch other videos of yours more proactively now that I know you're here. Keep up the good work

thanks, not sure but seems like we're getting no in-flow on our bosch this morning so I'll give this part a check.

Thank you! I want to pull the dishwasher door the other day and the thing went to the floor and crashed. I couldn’t believe it. We have had so many problems with this dishwasher. We’re eventually going to get another one, but we would like to string it along for a little longer.

Thanks bro. Just sorted mine out.

2:16 didn't realize I had to lift up and ended up breaking on the tabs on the side side. Wish I peeped this vid beforehand

How did you troubleshoot the door switch being the culprit and not the drive belt or the motor going bad?

Awesome video,worked perfectly on my dryer thank you!!!